CLIMATE INSTRUMENT CO.,LTD

Electro-dynamic Vibration Testing Machine

Group Environmental Vibration Test Chamber
Min. Order 1 piece
Terms of Payment L/C, D/A, D/P, T/T
Update Time 2018-10-11
Item specifics
product nameVibration Testing Machine
Max. Payload500 kg
Magnetic flux leakage≤1 mT
Weight (unpacked)2,500 kg
Description

Electro-dynamic Vibration Testing Machine


Description:

Electro-dynamic Vibration Testing Machine adopted the 'double-magnetic circuit structure','self-generated skeletonaction circles', 'Airborne Support' and 'roller bearings and linearguidance','trunnion isolation' advanced modern technology and specialtechnology, can be completed in X, Y, Z three-axis sinusoidal vibration testand broadband random vibration tests, to be completed by the classical (half -sine, trapezoidal, sawtooth wave)  pulseand shock response spectrum test. It widely used in national defense, weapons,aviation, aerospace, communications, electronics, electrical appliances,communications, home appliances and other fields.  


Performance Data Sheet

Shaker (Model# EDM-2000)

Sine force (peak)

30kN

Shock force (peak)

60 kN

Frequency range

52,600 Hz

Displacement (continuous)

100 mm

Max. Velocity

1.8 m/s

Max. Acceleration

75 G

Armature Diameter

445 mm

1st order resonant frequency

2,400 Hz

Allowable eccentric moment

500 Nxm

Armature weight

40 kg

HE/ST screw dimension

M10 (metric)

Axial vibration isolation frequency

3 Hz

Max. Payload

500 kg

Magnetic flux leakage

1 mT

Dimensions (L×W×H, unpacked)

1,330x860x1,250 mm

Weight (unpacked)

2,500 kg

Installation

Rubber mat (anchor bolts required)

Power Amplifier (Model# VSA-H323A)

Amplifier output

30 kVA

SNR

65 dB

Rated output voltage

120 Vrms

Amplifier efficiency

90%

Dimensions (L×W×H, unpacked)

800x900x2,100 mm

Weight (unpacked)

500 kg

Blower (Model# PBL-W30)

Air volume

0.66 m3/s

Power

15 kW

Air duct diameter

200 mm

Air pressure

0.075kgf/cm

Installation

Able to connect to ceiling (up to two 90 degree bends), max 20’ run

Horizontal Slip Table (Model# 30ST-600M)

Dimensions

600x600 mm

Thickness

40 mm

Frequency limit

2,000 Hz

Effective mass

54 kg

Note:

1. High pressure oil-film bearing is used for better uniformity.

Vibration Controller and Accelerometer

Vibration Controller VT-9008-4

4 Channel Vibration Controller with Sine and Self Calibration.

Accelerometer   EA-YD-181

100mV/g, Range: 50g, Working Freq.: 1-10kHz, Weight: 11gram, with 10ft low noise cable

Other supported functions/accessories

Environmental chambers

Supported

Mobile devices

Customizable

Insulation boards

Customizable

Fixture

Customizable

Working environment of the system

Temperature range

0-40

Humidity range

090% , no condensation

Power requirements

380V/3ph/50Hz, 65kVA

Compressed air pressure

0.6 Mpa


How to use

1, the controlmanual to complete the procedure

2, such asOperation error so that can not work, you can use the recovery method of thesteps of the input, and then set a single group or other running steps.

3, before use topress the external start switch, appears COO namely lets go, opens the key.

4, Taiwan Body:

1 The table bodyfoot sleeve as far as possible fixed

2 power supplyon/work in the output line can not be unplugged

3 Place the levelas far as possible

4 components canbe changed, the line should not be changed or from the connection.

5 The Taiwan bodymust not be all or part of the reorganization, only according to specificationsfor a single component and with the original confirmation password.

5, the amplitudeinside the code

1. Do not adjusttoo large before or after the boot

2) low-keyamplitude of high amplitude modulation

3 Control PanelAmplitude Knob placed in the middle position test items: placed to focus on themain point, reduce the left flat right.

4 control Box: Cannot be placed on the top or underground operation

6, Inside Code:

1) reset whenrunning or operating incorrectly

2) Control TheReset method step, each inside code only set one time to save can

3 usually must usethe internal code can not be set randomly

7, Control Box:

1) The connectingline of the body must be locked tightly after hanging

2 the vibrationdirection switch and the output connection line are correspondence, can notconnect the wrong

8, testing:Non-special test should use full wave test

9, the Taiwanbody: can not produce the collision sound, the upper and lower center axismutual touch will cause the spring steel piece rupture to be immediately shutdown, amplitude modulation is adjusted small then turns on.

10, other unknown:

Do not arbitrarilychange internal components and lines

11, the reason isbad:

1 The use ofcomputer models can not be used for shaking table control

2 can not reloadthe driver

2, for the Ista-iatest, the operator to protect the sample, to prevent the test pieces slide outof the table;

3, gear gearboxreplacement regularly;

4. Cut off allpower when not working, keep clean; 5, non-staff can not operate at will;


Electro-dynamic Vibration Testing Machine Image

Electro-dynamic Vibration Testing Machine